How To Replace Shutters: Two Different Approaches

0
27

How To Replace Shutters

In the old days, shutters were used to block the sun’s heat and protect the windows’ glasses. This was expensive back in the day and hard to get as well. However, things are different now as window shutters are one of today’s house’s most decorative parts.

Shutters require extreme care as they can become rotten easily if not repainted at least once a year. In this article, you will know how to replace shutters from both old wooden exteriors and plastic windows.

Things To Know About Replacing Shutters

Many things can happen if you do not replace and fix your shutters regularly. Before diving into the steps of replacing shutters from different windows, you should remember these following things.

Windows Can Be Replaced Without Replacing Shutters

This is one of the most common inquiries across the world. Many people are confused about whether they can replace windows without replacing shutters. Well, the answer is almost always yes. It is simple and easy to do.

Installing New Shutters

Several people think that it is necessary to do some special work to install new shutters. However, this is a completely wrong impression. There are shutter companies that produce perfectly shaped shutters for any windows.

Things Needed To Replace Shutters

The following equipment is needed for reparation volet of a shutter from windows:

  • Chisel
  • Hammer
  • Screwdriver
  • Tape measure
  • Caulking composite
  • Soft-haired brush
  • Caulking gun
  • Pry bar
  • Stepladder
  • Plastic bag
  • Workbench
  • Damp cloth
  • Drill Pencil
  • Safety goggles

How To Replace Shutters: 6 Steps To Replace Old Wooden Shutters

Here are the 6 simplest steps to replace shutters from wooden, vinyl, or aluminum windows:

  1. First, remove the worn-out shutter from the boundaries. If they are attached with nails, you will have to pry them off. Or, you can unscrew or remove all the screws.
  2. After that, you will be required to keep the vinyl shutters against the windows at the house’s borders. The shutters should be positioned so that there is equal space between the top and bottom edges of both the shutter and the window.
  3. Next up, you would want to place the shutter on a flat surface. Then mark on the point that is 11/2 inches inwards the top and bottom edges of the shutter. This mark is made on the rails. You should also mark on the wall that reflects the marks made on the shutter rails.
  4. Following this, you will now have to drill a 1/4-inch hole on the marks. Make sure to wear safety goggles.
  5. You will also have to drill holes on the walls where you made marks on the 3rd step. You should drill a 1-quarter deep hole. Make sure not to penetrate the sheathing of the house.
  6. Finally, you can place the shutter aligning with the top and bottom edges. Screw on the holes, and you have successfully replaced the old wooden shutter with a new vinyl one.

How To Replace Plastic Window Shutters [7 Steps]

The following 7 steps are the easiest guide to replace plastic window shutters:

  • The first step is to use the ladder properly and carefully to reach the topmost of the shutter.
  • Then use the screwdriver to remove the screws. Set the screws beside in a plastic bag. Then, remove the whole shutter with hinges from the wall.
  • After that, put the chisel at the back of the shutter and beat it with a hammer. Do this until the chisel penetrates the stem of the plug attached to the back of the shutter. Once you are finished with this activity, use the drill to extract the remaining of the plug.
  • After removing the shutter from the wall, you ought to be cleaning it. Use the soft-haired brush for this process and the damp cloth to clean the dust. The caulking components can be used to fill the holes on the wall.
  • Now get a new shutter and place it on the wall. You will now be required to mark the fitting points with a pencil. There will be 4 plugs, so 4 markings on the wall for a small shutter, and for a large shutter, there will be 6 plugs, so 6 markings on the wall.
  • After marking the plug points on the wall, you will have to drill holes. Keep your shutter on the ground while performing this part. Moreover, make sure to drill holes on the shutter as well.
  • You may require a helping hand in the final stage who can hold the shutter against the wall. You can reinstall the screws you extracted in the second step and use the screwdriver to attach them to the new shutter. Additionally, the plugs should be drilled through 13/4 inches deep into the wall after putting into the shutter holes. Once everything is attached, your work is done.

Conclusion

There are several reasons for changing and repairing a shutter from a window. The significance of knowing how to replace shutters cannot be stretched enough. The steps of replacing the two kinds of shutters can be beneficial for beginners as well as professionals.

LEAVE A REPLY

Please enter your comment!
Please enter your name here